What Size Cabinet Pulls? A Sizing Chart by Door and Drawer Width
Youโve picked your cabinets, settled on a finish, and found hardware you love. Now comes the hard part: figuring out what size pulls to order.
Cabinet pulls are small details, ones that might seem inconsequential at first, but their proportions can change how your entire kitchen looks. Go too small, and wide drawers can look awkward. Go too big, and the hardware can overwhelm the cabinet doors.
Should a 30-inch drawer have a 5-inch pull or a 10-inch one? Can you use the same hardware on every cabinet? And what exactly does โcenter-to-centerโ mean when youโre shopping?
This cabinet pull size guide was written to help take some of the guesswork out of choosing hardware. Use the charts below to match pull lengths to your cabinet and drawer widths, then learn where to position them before drilling.
And if youโre still exploring finishes and designs, browse these kitchen cabinet hardware ideas for inspiration.
The short answer Start with a pull about one-third the width of your drawer front. Thatโs about 10 inches long for a 30-inch drawer or 8 inches for a 24-inch drawer. For cabinet doors, try a 3- to 5-inch pull mounted vertically, or 8 to 18 inches for tall pantry doors. Check both the overall length and the center-to-center hole spacing before you order.
Cabinet pull size chart by drawer width
| Drawer width | Overall pull length | Center-to-center spacing |
|---|---|---|
| 6 to 11 in. | 3 to 4 in. | 3 in. (76 mm) |
| 12 to 17 in. | 4 to 6 in. | 3 to 5 in. (76 to 128 mm) |
| 18 to 23 in. | 6 to 8 in. | 5 to 6 5/16 in. (128 to 160 mm) |
| 24 to 29 in. | 8 to 10 in. | 6 5/16 to 8 in. (160 to 203 mm) |
| 30 to 35 in. | 10 to 14 in. | 8 to 12 in. (203 to 305 mm) |
| 36 to 42 in. | 12 to 18 in. | 10 to 16 in. (254 to 406 mm) |
A good starting point is to choose a pull thatโs approximately one-third the width of your drawer. Larger pulls can work especially well in modern kitchens, while shorter pulls tend to suit traditional cabinetry. Use the cabinet pull size chart above to narrow your options.
Note that these are suggested starting ranges, not fixed requirements. Center-to-center cabinet pull measurements vary by manufacturer and may not correspond to a particular overall length. Always check the product specifications before ordering.
You can also download the printable cabinet pull size chart (PDF), with placement tips and a worksheet for your hardware list.
Before you choose a size, measure the actual drawer front rather than assuming it matches the cabinetโs listed width. Cabinet construction can affect those dimensions. Our guide to standard kitchen cabinet sizes explains the measurements youโre most likely to encounter.
What size pull for a 30-inch drawer?
A 30-inch drawer is a perfect candidate for a 10-inch pull. Following the one-third rule, 30 divided by three equals 10. A pull around that length creates a balanced appearance without looking undersized.
For a more contemporary kitchen, you could increase the length to 12 or even 14 inches. If you prefer understated hardware, an 8-inch pull may work. Just remember that a 10-inch overall pull doesnโt necessarily have 10-inch screw spacing. Check the center-to-center measurement separately.
What size pull for a 27-inch cabinet?
First, determine whether youโre measuring a drawer or a cabinet with doors.
For a 27-inch-wide drawer, a pull approximately 9 inches long is a comfortable starting point. You might choose an 8-inch or 10-inch model depending on whatโs available.
For a 27-inch cabinet with two doors, youโre working with two narrower door fronts, not one 27-inch surface. Each door might look better with a compact 3- to 5-inch pull mounted vertically.
What size pull for a 24-inch drawer?
For a 24-inch drawer, start with a pull about 8 inches long overall. Pulls with 160 mm (6 5/16-inch) or 192 mm (7 9/16-inch) hole spacing are worth comparing, but their overall lengths vary by design.
For example, the Amerock pull in the center-to-center section below has 160 mm hole spacing and measures 7 1/16 inches end to end. Check each productโs overall length to find one close to 8 inches. The hole spacing alone wonโt tell you.
Pull sizes for doors and tall cabinets
Cabinet door pulls usually mount vertically on the side opposite the hinges, so a doorโs height and style matter more than its width. The ranges below give you a place to start.
| Cabinet front | Pull length | Good to know |
|---|---|---|
| Wall and base cabinet doors | 3 to 5 in. | Mount vertically near the corner opposite the hinges. Common spacing: 3 in. (76 mm) or 3 3/4 in. (96 mm). |
| Two-door cabinets | 3 to 5 in. per door | Size each pull to its own door. A 27-inch cabinet with two doors gets two door-size pulls. |
| Tall pantry doors | 8 to 18 in. | Longer pulls can suit full-height doors. Hold the pull in place to check the proportions and make sure itโs comfortable to reach. |
| Paneled appliances | 12 in. and up | Use appliance-rated pulls on refrigerator and freezer doors. Theyโre commonly sold in 12, 18, and 24 in. center-to-center sizes. Check the appliance makerโs mounting requirements. |
What is the one-third rule for cabinet pulls?
The 1/3 rule for cabinet pulls recommends choosing a pull about one-third the width of a drawer. For example, an 18-inch drawer would have a 6-inch pull, a 24-inch drawer an 8-inch pull, and a 36-inch drawer a 12-inch pull.
Itโs a guideline, though, not a set-in-stone requirement. For cabinet doors, shorter vertical pulls near the opening corner often work better. Ultimately, the right size depends on your cabinet style and personal preference.
Center-to-center vs. overall length: know what youโre ordering
Cabinet pulls have two measurements that are easy to confuse:
- Overall length: The total length of the pull from end to end, which determines how large it looks.
- Center-to-center (CTC): The distance between the centers of the mounting holes, which determines where you drill.
For example, an Amerock cabinet pull with 6 5/16-inch center-to-center spacing measures 7 1/16 inches overall. If youโre replacing hardware, matching the existing center-to-center spacing saves you from drilling new holes. Some of the most common sizes include 3 inches (76 mm), 3 3/4 inches (96 mm), 5 1/16 inches (128 mm), and 6 5/16 inches (160 mm).
Many pulls list their hole spacing in millimeters. Use this table to compare common sizes in inches, then check the pullโs overall length against your drawer front.
| Metric | Inches | Good for |
|---|---|---|
| 76 mm | 3 in. | Doors and 6 to 17 in. drawers |
| 96 mm | 3 3/4 in. | Doors and 12 to 17 in. drawers |
| 128 mm | 5 1/16 in. | 12 to 23 in. drawers |
| 160 mm | 6 5/16 in. | 18 to 29 in. drawers |
| 192 mm | 7 9/16 in. | 24 to 29 in. drawers |
| 224 mm | 8 13/16 in. | 30 to 35 in. drawers |
| 256 mm | 10 1/16 in. | 30 to 42 in. drawers |
| 320 mm | 12 5/8 in. | 36 to 42 in. drawers |
What size pulls for different cabinet door styles?
Cabinet door style affects how pulls look and where they can be installed, even when the doors are the same size.
Shaker cabinet doors
Shaker cabinets have recessed center panels surrounded by vertical stiles and horizontal rails. These frames provide natural hardware placement but limit where you can drill.
Short vertical pulls typically work best on the stile near the opening edge. Longer pulls may extend into the recessed panel, so make sure the mounting posts have adequate support. Measure the stile width and check the back of the door before choosing hardware.
Slab cabinet doors
Slab doors have flat, uninterrupted fronts, allowing more flexibility with hardware placement. Short pulls offer a subtle look, while longer or oversized pulls emphasize the clean lines of modern cabinetry. You can also experiment with horizontal placement without worrying about recessed panels.
Raised-panel cabinet doors
Raised-panel doors feature decorative details, including beveled or contoured surfaces. Short, simple pulls or knobs complement the design without overwhelming it. Install hardware on flat sections of the frame, avoiding decorative edges.
Still choosing cabinetry? Compare these and other cabinet door styles before selecting your hardware.
Where should cabinet pulls be placed?
Even the perfect pull can look awkward in the wrong spot. Paying attention to the ideal cabinet hardware placement makes your cabinets easier to use and gives your kitchen a polished look. Hereโs where to position each pull.
| Cabinet type | Typical pull placement |
|---|---|
| Upper cabinet doors | Vertically near the lower corner opposite the hinges |
| Lower cabinet doors | Vertically near the upper corner opposite the hinges |
| Small and medium drawers | Horizontally centered on the drawer front |
| Deep drawers | Horizontally centered or positioned toward the upper portion |
| Shaker drawers | Centered or mounted on the upper rail, if space allows |
On upper cabinet doors, position vertical pulls about 2 to 3 inches from the bottom edge, aligned with the stile. For lower doors, place them the same distance from the top. Measure that distance from the doorโs edge to the nearest end of the pull.
For drawers, center the pulls horizontally. On a 30-inch drawer with 8-inch center-to-center spacing, drill holes 11 and 19 inches from one side. Vertical placement depends on the drawerโs height and design.
How to mark holes before drilling
Once youโve chosen your pulls, follow these steps:
- Find the center. Measure the drawer front and mark its horizontal midpoint.
- Measure the hole spacing. Divide the pullโs center-to-center measurement by two and mark that distance on either side of the midpoint.
- Check the height. Keep the holes level and positioned consistently across similar drawers.
- Make a template. Use a cabinet hardware jig or a cardboard template to repeat measurements.
- Test before drilling. Hold the actual pull against the cabinet to confirm its position and check for interference.
Use the drill bit size specified by the hardware manufacturer, and protect the back of the door or drawer front from splintering. If youโre drilling into Shaker or raised-panel cabinetry, confirm that both mounting locations have adequate support.
Can you mix knobs on doors with pulls on drawers?
Absolutely. Mixing knobs on doors with pulls on drawers is a design choice that works especially well in traditional, farmhouse, and transitional kitchens. Knobs keep doors simple, while pulls make drawers easier to open, particularly when theyโre loaded with heavy cookware.
For a cohesive look, choose complementary shapes and matching finishes, such as brushed brass knobs with brushed brass bar pulls. You can vary pull lengths, too. A 15-inch drawer might use a 5-inch pull, while a 30-inch drawer gets a 10-inch version of the same style.
Choose knobs and pulls from the same brand and collection when you want the finishes to match. Brushed brass from one brand can look different from another. If youโre mixing brands or collections, order one of each and compare them in your kitchen before buying the full set.
For more tips, see our guide on how to choose kitchen cabinet hardware.
What about oversized pulls for pantry doors and appliances?
Standard pulls can look undersized on tall pantry doors. Longer pulls, typically 8 to 18 inches, create better proportions, especially on modern, full-height cabinets. Choose a placement thatโs comfortable to reach and use.
Paneled refrigerators and dishwashers may also benefit from oversized handles, but they often require appliance-rated pulls designed for heavier loads. Check the appliance manufacturerโs mounting requirements before you order.
Should you use one long pull or two smaller pulls on wide drawers?
For drawers wider than 30 inches, you can use one long pull or two smaller ones. A single pull creates a clean, modern look and makes the drawer easy to open from the center. Two evenly spaced pulls offer a more traditional style.
For heavy drawers holding pots and pans, one long pull is often more practical since pulling from just one side can put uneven pressure on the drawer slides.
Find the right hardware for your kitchen
You donโt need identical pulls on every cabinet or a complicated formula for choosing hardware. Start with your drawer and door measurements, use the sizing chart to narrow your options, and check the actual dimensions before drilling.
Keep a copy of the chart handy while shopping so you can compare sizes without measuring everything twice.
Print the cabinet pull size chart
It has the size charts, a placement guide, and a worksheet to record your measurements, pull sizes, and quantities before you order.
And if youโre still planning your remodel, you can shop kitchen cabinets in styles that complement your favorite hardware.
Need help with your layout? Our free 3D kitchen design service includes a layout and an itemized quote, so you can plan your cabinets before choosing the hardware.
Common questions about cabinet pull sizes
What size pulls for kitchen cabinets?
For standard cabinet doors, compact pulls around 3 to 5 inches overall are a common starting point. Drawer pulls usually increase with drawer width. A 24-inch drawer, for example, often looks balanced with a pull approximately 8 inches long.
Is there a standard cabinet pull size?
Three-inch (76 mm) center-to-center spacing is a familiar standard, but many other sizes are available. Thereโs no single pull size suitable for every cabinet or drawer.
What size pulls for 36-inch drawers?
A 12-inch overall pull follows the one-third rule. You can go longer for a bold, contemporary look or slightly shorter for something more understated. Check the available mounting-hole spacing before ordering.
Should all cabinet pulls be the same size?
No. Using different lengths from the same hardware collection often looks more balanced than using identical pulls everywhere. Keeping the finish and design consistent helps tie everything together.
Are 5-inch or 6-inch cabinet pulls better?
It depends on the cabinet width, door style, and the manufacturerโs measurements. Either can work on a medium-sized drawer. Compare overall lengths rather than assuming the advertised sizes describe the entire handles.
How do you measure existing cabinet pulls?
Remove one pull and measure from the center of one screw hole to the center of the other. Thatโs the center-to-center dimension youโll need when ordering replacements.
Are 3-inch cabinet pulls too small?
They work well on cabinet doors and small drawers. Check what the 3 inches measures, though: a pull with 3-inch (76 mm) hole spacing is longer than 3 inches overall. On drawers 24 inches and wider, the size chart starts at 8-inch pulls, so a 3-inch pull will probably look small there.
How many cabinet pulls do I need?
Count the doors and drawers where you plan to use pulls, leaving out any that will have knobs. Allow one pull for each, or two on wide drawers if thatโs the look youโve chosen. Include false drawer fronts only if you plan to add decorative hardware. Order one or two spares in case a pull gets damaged or the style is discontinued.